Home > HARDWARE > CONSTRUCTION HARDWARE > JOIST HANGERS & CONNECTORS
Choose a sub category:
JOIST HANGERS FRAMING ANGLES/ANCHORS MENDING PLATES
NAIL PLATES POST ANCHORS / CAPS FENCE BRACKETS
BRIDGING INSULATION SUPPORTS STRAPS
PLYWOOD CLIPS FOUNDATION ANCHORS BRICK/WALL TIES
MISC CONSTR HARDWARE
Sort By:
1 2 3 ... 5
USP Lumber JL26IF-TZ Standard Invert Flange Joist Hanger USP Lumber RT16ATZ Double Plate Hurricane/Seismic Anchor USP Lumber JL28IF-TZ Standard Invert Flange Joist Hanger
Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Anchor tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces. Typical Truss/rafter to double plate installation. Requires Meet ICC-ES ESR-1465 and FL817 codes. Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber JUS210-2TZ Double Shear Slant Joint Hanger RH Tamlyn PC1532 Plywood Clip RH Tamlyn PCS716 Plywood Clip
Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. With built-in spacer for use when support spacing exceeds the maximum length of an unsupported edge. Boxed. Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed.
RH Tamlyn PCS12 Plywood Clip RH Tamlyn PCS1532 Plywood Clip Squeek No More 1011345 Screw Set
Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed. Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed. Specially scored waxed screws. Scored head breaks off at the same place every time. Carded.
RH Tamlyn PCS58 Plywood Clip Acorn IHW16100 Insulation Support Wire 16 in L USP Lumber NA11-5MC Joist Hanger Nail
Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. Structurally rated. For use with MiTek/USP Lumber Connectors' products. For additional information including withdrawal load and allowable shear per nail, please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber NA9-5MC Joist Hanger Nail Squeek No More 1010543 Floor Squeak Repair Kit Acorn IHW24100 Insulation Support Wire 24 in L
Structurally rated. For use with MiTek/USP Lumber Connectors' products. For additional information including withdrawal load and allowable shear per nail, please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Eliminate squeaks quickly and permanently. Can be applied to 2nd floors, hardwood floors, carpet, and stairs. Each kit contains: 1 - alignment and depth control fixture, 50 - specially scored waxed screws, 1 - special driver bit, 1 - complete instruction kit. Carded. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge.
Deckmate 90166 Deck Bench Bracket with Bench Bracket USP Lumber RS20-R Coiled Strap Acorn IHW16500 Insulation Support Wire 16 in L
You determine the size. Connect with railing brackets with 2x4 and 2x6 lumber to easily add a bench to any size or shape deck. Gain increased seating area while using only 7" of deck space. Assembled unit stands 36"H for deck railing, seat is 17"H. Quick and easy to assemble using basic tools. Includes bench bracket, hardware and instructions. LUMBER NOT INCLUDED. Enables cut-to-length convenience for job site needs. G90 galvanizing finish. 1-1/2" nail spacing. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge.
ANGLE 2X4IN TRIPLE ZINC 12GA  RH Tamlyn BT 22SP Corrugated Straight Brick Wall Tie RH Tamlyn BT22ZZSP Corrugated Scalloped Zig Zag Brick Wall Tie
Provides a 90? connection for medium/heavy duty applications; stronger than angled nailing or screw fastening; help ensure joints are consistently straight and strong. Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8". Boxed. Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8".
Hopkins 90128 Shelf Link 4 ft L x 2 ft W USP Lumber PAU66-TZ Post Anchor RH Tamlyn BT28ZZ5SP Corrugated Scalloped Zig Zag Brick Wall Tie
You can determine the size and configuration, just add 2x4's to the ShelfLinks to make functional and custom shelving in any length, height and configuration. Made of structural resin. Can support spans up to 8'. Includes ShelfLinks, hardware and instructions. LUMBER NOT INCLUDED. Used to secure wood posts to concrete footings and to provide moisture damage protection. Higher uplift resistance an optional bolt fastening to post. Features a 1" stand-off plate to evaluate wood posts above concrete surfaces. Drain slots allow the anchors to shed water. Triple zinc finish for ACQ pressure treated lumber. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires (12) 16d HDG nails or (2) 1/2" HDG bolts and (1) 5/8" anchor bolt for installation. Meets ICC-ES ESR-1881, FL821, L.A. City RR 25779 and Dade County, FL 07-0306.06, PAU44-TZ and PAU66-TZ codes. Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8".
RH Tamlyn BT28500SP Corrugated Straight Brick Wall Tie USP Lumber RT7A Double Plate Hurricane/Seismic Anchor USP Lumber JL24 Standard Joist Hanger
Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8". Boxed. Ties trusses and rafters to top plates. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. Triple Zinc anchors (310.1573) requires 8d HDG nails and Gold Coat anchors (947.3265) requires N8-GC nails.  Meets ICC-ES ESR-1465 and FL817 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. G90 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber ST12 Strap Tie USP Lumber BL Corner Brace USP Lumber JA1 Joist Angle
Connects wood framing to resist tension forces. G90 galvanizing finish. ST Medium-duty series require 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. 16 Gauge. Reinforces 90 degree wood-to-wood connections. G90 galvanizing finish. Requires 16d nails for installation. 12 Gauge. Used to strengthen framing in various applications or to support joists where stirrup style hangers cannot be installed. Requires 10d x 1-1/2 nails for installation. Meets ICBO, SBCCI, BOCA - NER 505; L.A. City RR25303, DSA PA-076; and Dade County, FL 98-0421.06 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 16 Gauge.
   
 
1 2 3 ... 5